Most ISPs provide their customers with modems-aka gateways-that have routers built in. Step 2: Configure your wireless router gateway
Many newer routers, such as the TP-Link Deco M5 show here, have auto-sensing ethernet ports that configure themselves for WAN or LAN duty based on the signal they receive from the cable. You’ll need to perform some preliminary steps first, so don’t disconnect or turn anything off just yet. Some routers have a designated WAN (Wide Area Network) port for connecting to the gateway, while others have auto-sensing ports that automatically configure themselves as WAN or LAN (Local Area Network, i.e., your home network). Instead, place the node where its wireless signal can reach that dead spot. Mesh systems need not be expensive-our favorite budget pick, TP-Link’s Deco M5 three-pack is just $150.īut, caution: Don’t put a wireless node in a Wi-Fi dead spot-it won’t be able to connect to your network any better than any client device. Your data will wirelessly hop from one node to the next, and you’ll have a strong Wi-Fi signal nearly everywhere in your house. In this system, you locate one node wherever your gateway is, and then place subsequent nodes in different rooms of your home. If you’re really ambitious, you could run a pair of ethernet cables through your walls to that ideal central location (one cable to connect the router to your gateway, and a second to connect it to an ethernet switch-perhaps in the closet with the gateway).īut there’s also an easier option: a mesh-style router. You don’t need to move the gateway, but you can use a longer (and very inexpensive) CAT5e or CAT6 cable to connect the router to the gateway’s ethernet port so you can put it out in the open. If you can’t put your wireless router in the center of your home, at least try to avoid putting in a closet that will crimp its range. There just happens to be a wet bar at the center of my home. The best place to locate your router is in the center of your home. That equipment (be it a cable or DSL modem or-if you’re really lucky-a fiber gateway) is invariably installed at a perimeter wall. It’s also impossible for most people to do, because you need to connect your router to the broadband gateway for your internet service provider (ISP). That will provide the most even coverage. Step 1: Place your wireless routerĪs any router manufacturer will tell you, the best location for your wireless router is in an open area in the center of your home.
#Can i use the same router for mac and pc Pc#
I think it’s best to have both options so you can decide (personally, I prefer using the browser because the display connected to my PC is bigger and easier to see).
Some companies no longer even bother with a browser-based user interface. This is how you can use Mac as a wireless router.These days your router is likely to have a companion app, making it possible to do your initial installation and subsequent tweaking on your smartphone or tablet. That is it! A green light across Internet Sharing : ON option will indicate that the a wireless network has been created and you are good to connect to it. Click on OK button and then put a check across Internet Sharing option and then click on Start button.Click on the WiFi Options just below it and enter the details as below (In the channel option, leave whatever is given to you by default).Now just below that, put a check across the WiFi option in the To computers using section.Just click on it and choose Ethernet option At the option labelled as Share your connection from, you will find a drop down.Now click on the Internet Sharing from the options on the left panel (but do not put check across it now, we will do it later).Click on the Lock, and enter the credentials of your Mac to ensure that all your further steps are preserved.Click on the Sharing option under Internet & Wireless section.Now launch the System Preferences option.But this cable should be coming from modem (Mac can only act as router, not as a modem).First thing you need to do is plugin in Ethernet cable into your Mac and see if the Internet connection is working fine.
#Can i use the same router for mac and pc how to#
Cool, right? Lets learn how to do it then. All that is needed to be done is plug in the LAN cable / Ethernet cable into your Mac, and do some tweaking after which your Mac will be turned into a router. So, here I am sharing this Mac tutorial.īelow steps can you followed to use a Mac as a wireless router.
Yes, I was disappointed because I do not prefer buying things, if the same purpose can be served for free. I discovered that I can use my Mac as a wireless router, but by that time I already bought a router.
0 kommentar(er)
